Add tcp-udp docs

packages/docusaurus/docs/02-Getting Started/07-tcp-udp.md

@@ -0,0 +1,93 @@
+# TCP & UDP Support
+
+Pangolin supports raw TCP and UDP traffic because under the hood Badger and Newt are just using basic WireGuard tunnels that can pass anything! There is a little manual setup you need to do before you can create a raw TCP or UDP resource:
+
+## Configuring Firewall
+
+This is highly OS and VPS dependent. Just in the same way you opened port 51280, 443, and 80, you need to open your desired port to your VPS so that Traefik can pass traffic out to the internet.
+
+## Configuring Docker
+
+If you are using the standard install with a Docker network you will need to expose your ports from the Gerbil Docker container as well. This can be done by simply adding a port mapping to the docker-compose.yml file you can find in the root where you installed Pangolin:
+
+```yaml
+gerbil:
+  ...
+    ports:
+        - 51820:51820/udp # LEAVE ALONE: For Wireguard
+        - 443:443 # LEAVE ALONE: For HTTPS
+        - 80:80 # LEAVE ALONE: For HTTP
+
+        - 1704:1704/udp # ADDED
+        - 1602:1602 # ADDED
+```
+
+:::tip
+
+After editing the Docker Compose config you need to restart it! You can do `sudo docker compose up -d`
+
+:::
+
+## Configuring Traefik
+
+Once you have opened the port on your firewall you need to create an "EntryPoint" in Traefik. "EntryPoints are the network entry points into Traefik. They define the port which will receive the packets, and whether to listen for TCP or UDP. (Traefik Labs 2024)" Unfortunately this must be done manually because Traefik does not support pulling EntryPoints from dynamic config locations.
+
+But this is pretty simple! All you need to do is edit your Traefik config in `config/traefik/traefik_config.yml` with your favorite editor and add a new entry to the `entryPoints` section.
+
+So for example a UDP EntryPoint would look like:
+
+```yaml
+entryPoints:
+  udp-1704:
+    address: ":1704/udp"
+```
+
+And for TCP:
+
+```yaml
+entryPoints:
+  tcp-1602:
+    address: ":1602/tcp"
+```
+
+:::info
+
+The *name* if the EntryPoint is IMPORTANT because it must be referenced by the dynamic config. ALWAYS name your EntryPoint in the format `protocol-port` as shown in the examples!
+
+:::
+
+The whole thing would look something like this:
+
+```yaml
+entryPoints:
+  web:
+    address: ':80'
+  websecure:
+    address: ':443'
+    http:
+      tls:
+        certResolver: letsencrypt
+    transport:
+      respondingTimeouts:
+        readTimeout: 30m
+    tcp-1602:
+        address: ":1602/tcp"
+    udp-1704:
+        address: ":1704/udp"
+```
+
+:::tip
+
+After editing the Traefik config you need to restart it! You can do `sudo docker compose restart traefik`
+
+:::
+
+## Create the Resource
+
+Finally! Now after all of that config you can create the resource in Pangolin. You can simply create a new resource and toggle the HTTP switch off. This will allow you to enter the SAME point you configured above and the protocol.
+
+<p align="center">
+    ![graphic](./img/create_udp_resource.png)
+</p>
+
+After you create the resource you can add targets just like any other resource!